Teledyne 465L Bedienungsanleitung PDF herunterladen (Seite 28)

Teledyne API Model 465L O

Monitor Instruction Manual

26 05509F DCN6409

Figure 4-5. M465L Pneumatic Diagram with Sample Conditioner and Permeation Gas Dryer Options (in single-

stream configuration)

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 91 92

OPERATION MANUAL 1
MODEL 465L 1
OZONE MONITOR 1
Notice of Copyright 3
Trademarks 3
IMPORTANT SAFETY INFORMATION 5
CONSIGNES DE SÉCURITÉ 6
ABOUT THIS MANUAL 7
REVISION HISTORY 8
TABLE OF CONTENTS 9
Teledyne API Model 465L O 10
Monitor Operation Manual 10
FIGURES 11
Teledyne API Model 465L O 13
1. INTRODUCTION 15
APPROVALS 17
2.2. Approvals 18
3. PRINCIPLE OF OPERATION 21
4. GETTING STARTED 23
4.1. Pneumatic Connections 25
4.1.1. Sample Gas Connection 26
4.1.1.1. Sample Filtration 27
26 05509F DCN6409 28
Teledyne API Model 465L O 29
Monitor Instruction Manual 29
4.1.2. Exhaust Connection 30
Electrical I/O Connections 31
Configuration 31
4.2.2. Analog Output 31
4.2.3. Status Outputs 31
4.2.6.1. RS232 Connection 35
4.2.6.2. RS485 Connection 35
4.2.6.3. Ethernet Connection 35
05509F DCN6409 35 37
6. OPTIONS 39
7. OPERATION 41
Table 7-1: Alarm LED’s 42
7.2. Front Panel Menus 43
7.2.3. DIAG Menu 47
7.2.3.2. Signal I/O 48
7.2.3.3. Memory Reset 49
7.2.3.4. Zero Calibration 49
7.2.3.5. Span Calibration 50
Figure 7-4: Span Cal Menu 51
7.2.4. VIEW Menu 53
7.2.5. CONFIG Menu 53
7.2.6. SETUP-VARS Menu 54
7.2.7. SETUP-STREAM Menu 55
7.3. Multi-Stream Operation 56
8. DIGITAL COMMUNICATIONS 57
RS232 Configuration 58
RS485 Configuration 58
Ethernet Configuration 58
8.3. RS-232 Configuration 59
8.4. RS-485 Configuration 60
8.5. Ethernet Configuration 61
(DHCP Mode) 62
8.6. MODBUS Register Maps 63
62 05509F DCN6409 64
05509F DCN6409 63 65
64 05509F DCN6409 66
9.1. Maintenance Schedule 68
9.2. Instrument Layout 69
9.4. UV Lamp Adjustment 71
9.5. UV Lamp Replacement 72
Sensor Valve Replacement 74
Maintenance 75
9.11. Boot Loader Operation 76
9.11.2.1. Upload Firmware 77
9.11.2.2. Verify Firmware 78
10. TROUBLESHOOTING 80
10.1.2. Interconnect Diagram 81
LED’s or Status Outputs 82
10.2.1. Sensor OK 83
10.2.2. Invalid Reading 83
10.2.3. Check Lamp 83
10.2.4. Pneumatic Error 83
10.2.4.1. Pressure Too High 84
10.2.4.2. Pressure Too Low 84
11. CALIBRATION 86
12. SPARE PARTS 88
M465L NEMA Spare Parts List 89
88 05509F DCN6409 90
05509F DCN6409 90 92

Kommentare zu diesen Handbüchern

Keine Kommentare

Teledyne 465L Bedienungsanleitung Seite 28

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Teledyne 465L